Firmware Update

  1. How to update using device buttons
  2. How to update using Dashboard
  3. Release Notes
    1. Firmware Rev.3878 (2017.09.06)
    2. Firmware Rev.3846 (2016.12.02)
    3. Firmware Rev.3780(2016.5.10)
    4. Firmware Rev.3779(2016.04.16)
    5. Firmware Rev.3776(2016.02.25)
    6. Firmware Rev.3739(2015.12.03)

How to update using device buttons

  1. Make sure you are offline.
  2. Connect the AC adapter to the LiveShell 2
  3. Start live streaming so the device LCD changes to “Online”
  4. Press the top left device button and select “Power-Off.”
  5. If a newer firmware has been released, your LiveShell 2 will automatically update the firmware.
    Note: Do not unplug the AC adapter or remove the batteries while the firmware is being updated.

How to update using Dashboard

    1. Connect the AC adapter to the LiveShell 2.
    2. Open Dashboard.
    3. If there is a new firmware update,  an update notice will be displayed.

    1. Click “Update now.”

    1. Read the update warnings and click “Update.”

  1. Your LiveShell will begin to automatically update the firmware and will reboot.
    Note: Do not unplug the AC adapter or remove the batteries while the firmware is being updated.
  2. The status after rebooting is set by “After Online” settings. (The default is ” Auto Broadcast “)

Release Notes

Firmware Rev.3878 (2017.09.06)
Main Improvements
  • Fixed the problem that the AXIS IP camera compatibility function did not work.
  • Fixed RTSP description contents
  • Fixed the problem that the battery would drain when the AC adapter was removed during rebooting.
  • Fixed the problem that LiveShell 2 could not receive RTMP Acknowledgment Message and streaming distributionFixed the problem that LiveShell PRO could not receive RTMP Acknowledgment Message and streaming distribution, for example to Wowza Streaming Engine, stops. stops.
Firmware Rev.3846 (2016.12.02)
Main Improvements
  • Fixed the problem that a higher value than set is displayed as frame rate in RTSP mode.
  • Fixed the problem that a false Wi-Fi profile “Wi-Fi#10” appears when deleting a registered Wi-Fi profile.
  • Fixed the problem that “DNS error” occurs when LiveShell 2 is offline in RTSP mode then immediately restarts live streaming.
    Fixed the problem that in local mode an unexpected number is displayed.
  • Added support for Huawei E3131s-2 USB modem (12d1:1f01/14db) and Docomo L-03F USB modem.
  • Fixed issue where the alert message,”Please use a keyframe frequency of four seconds or less”, is shown in the YouTube Live control room even if required frequency is already set.
  • Fixed the problem that LiveShell 2 does not connect to Dashboard when name resolution fails.
  • Fixed the problem that LiveShell 2 hangs while stopping live stream when the device displays “Synchronizing Dashboard” or error messages.
  • Fixed the problem that LiveShell 2 does not accept commands to restart or to go offline when stopping live streaming while the device displays “Synchronizing Dashboard”.
  • Icons now immediately disappear when LiveShell 2 goes offline.
  • Added support for vertical crop 9:16 aspect ratio.
Firmware Rev.3780 (2016.05.10)
Main Improvements
  • Fixed the problem that LiveShell 2 cannot accept video and audio correctly from some HDMI sources.
Firmware Rev.3779 (2016.04.16)
Main Improvements
  • Fixed the problem that video is blank for the first several seconds after starting RTSP livestreaming.
Firmware Rev.3776 (2016.02.25)
Main Improvements
  • Fixed the problem that LiveShell 2 cannot update some RTSP livestreaming settings.
  • Fixed the problem that LiveShell 2 sometimes does not work properly during RTSP livestreaming.
  • Added support for 4G LTE/USB adapter (Huawei E3131s-2).
  • Fixed the problem that LiveShell 2 sometimes cannot send audio packets during RTSP livestreaming.
Firmware Rev.3739 (2015.12.03)
Main Improvements
  • Added a menu to show Wi-Fi MAC address.
  • Added changes to support LTE USB modem.
  • Fixed the problem that LiveShell 2 cannot update some USB modem settings.